High Power DC Electronic Load Model 63200A series 요약정보 및 구매

상품 선택옵션 0 개, 추가옵션 17 개

제조사 Chroma

관련상품

등록된 상품이 없습니다.

제품 정보

제품 기본설명

제품 상세설명

Key Features:
-Rated power: 2kW, 3kW, 4kW, 5kW, 6kW, 12kW, 18kW, 24kW, Max. 240kW (Parallel)
-Voltage range: 0-150V, 0-600V, 0-1200V
-Current range: 2,000A max. per unit
-CC, CR, CV & CP operation modes
-CR+CC, CR+CV, CC+CV complex modes
-Up to 10 units master/slave parallel control
-Dynamic synchronous control in static and dynamic loads
-User defined waveform (UDW)
-CZ mode for turn on capacitive load simulation
-External loading current simulation
-Auto frequency sweep up to 50kHz
-Real time power supply load transient response simulation & Vpk+/- measurement
-User programmable 255 sequential front panel input status
-Ultra high precision voltage & current measurement
-Precision high speed digitizing measurement/data capture
-Voltage, current & Pmax measurement for OCP/OLP tesing
-Timing & discharging measurement for batteries
-Instant overpower loading
-Short circuit simulation
-Smart fan control
-Full protection: OC (adjustable), OT,OP (adjustable) protection & OV warning
-Standard USB, optional Ethernet and GPIB interfaces 
 

APPLICATIONS

Chroma 63200A series Applications

ULTRA HIGH POWER DENSITY & USER-DEFINED HOT KEY DESIGN

Chroma's 63200A series high power electronic loads with digital signal microprocessor (200MHz) built in have the optimal speed and control performance. The ultra high density power (6kW@4U) not only saves room, its super high voltage (0.015%+0.015%F.S.) and current (0.04%+0.04%F.S.) measurement accuracy ensures the fidelity of results. In addition, the entire series can either be operated by hand or controlled remotely. For higher power demands, master/slave control can be used to parallel multiple units for operation. These electronic loads also have synchronous loading capabilities to simulate the actual loading status.

The world leading ultra high power density design overturns the concept of oversize and difficult moving high power electronic load. It saves plenty of room space and solves the space issue when upgrading the electronic load in an automated test system. Moreover, the 63200A provides 4 sets of user-defined hot keys that enable the user to enter the operation mode quickly.

ICONIC FUNCTION SELECTIONS

The iconic function selections make it easier for users to control/operate the 63200A series. The basic and advance functions are iconized, users can select the functions via the rotary or arrow keys. The abbreviations are shown in the icons and the full descriptions are shown on the VFD display for users to easily operate without the need for an operation manual.

FLIPPABLE FRONT PANEL

The 63200A series is equipped with flippable front panel for 7U, 10U & 13U height models with maximum flippable angles 70˚. This design allows convenient access to controls from any height.

FLIPPABLE FRONT PANEL

APPLICATION OF BASIC LOADS

The 63200A series electronic loads operate in constant voltage, current, resistance, or power modes to satisfy a wide range of test requirements. For instance, the CC and CR modes ensure that the UUT voltage outputs remain stable when the load varies. For battery chargers or charging stations, CV mode can change their output voltage to ensure the precision of the charging current. When the UUT is a battery, the electronic load changes to simulate device loading behavior. Many battery discharge applications and power consumption profiles can be simulated for analysis, making the CP mode the best choice for simulating electronic device loads.

APPLICATION OF BASIC LOADS

MASTER/SLAVE PARALLEL CONTROL

When the need is for increased power, two or more loads can be run in parallel to achieve the desired load current. The 63200A provides the user with smart Master/ Slave mode controls which enables the user to program the load currents of the Master and have them automatically calculated and downloaded to the slave loads. Using several loads in parallel to emulate a single load dramatically simplifies the operation. All models of the series can be integrated into a 41U standard rack to save space. The 63200A can be controlled and reconfigured with automated testing applications via standard USB or optional Ethernet and GPIB interfaces.

MASTER/SLAVE PARALLEL CONTROL

 

SINE WAVE DYNAMIC LOAD

The 63200A series has a unique sine wave loading function which allows setting of a current bias (I_DC), a loading sine wave (I_AC) and sine wave frequency. The sine wave loading must be greater or equal to zero ampere. This function can be used for D/D, server power supplies and fuel cells for DCIR testing.

SINE WAVE DYNAMIC LOAD

 

DYNAMIC LOAD

Modern electronic devices operate at very high speeds and demand rapid transient response characteristics. To address these applications, the 63200A series offers high speed, programmable dynamic loading (CCD: Dynamic Current Loading & CRD: Dynamic Resistance Loading) and sweep simulation for testing. The figure shown below exhibits the programmable parameters such as current high/low level, T1/T2, rise/fall rate and execution times. When the load current changes continuously, the internal monitoring mechanism and line circuit can minimize the current waveform distortion. The current rise minimum response time for model150V is 10μs and the dynamic change is up to 50kHz.

The dynamic mode provides a unique simulation capability allowing users to set the number of times each cycle repeats from 1~65535. This feature is very suitable for testing D/D converter and instant large withstand current of batteries.

DYNAMIC LOAD

DYNAMIC LOAD

 

DYNAMIC FREQUENCY SWEEP CONTROL

The 63200A also offers a unique dynamic frequency sweep (as shown on the right) with variable frequencies up to 50kHz. This capability is ideal for determining worst case voltage peaks. Measurement of the Vpeak (+/-) can be achieved using this function with a sampling rate of 500kHz. The dynamic loading mode can simulate different loading conditions for most test requirements. Dedicated remote load sensors and control circuits guarantee minimum waveform distortion during dynamic loading.

DYNAMIC FREQUENCY SWEEP CONTROL

 

CONSTANT IMPEDANCE MODE (CZ MODE)

There are many capacitors on the mainboard of PC. To prevent the inrush current from occurring and trigger the over current protection of server power (since the server power charges the capacitors on the mainboard). It is necessary to test the capacitive loading when turning on the power supply. Therefore, the 63200A series provides the CZ mode for this test.

The unique CZ mode designed in 63200A series can improve the loading behavior of CC & CP mode and makes the simulated loading current more realistic.

CZ mode 

ULTRA HIGH PRECISION MEASUREMENT

The 63200A series provides three operating and measuring ranges. Take 63206A-150-600 for example, three voltage ranges of 16V/80V/150V which can meet the requirements of server power or telecom power (12V, 48V, 54V) testing; three current ranges of 60A/300A/600A which can provide different applications of current operating and can minimize the measurement error by selecting the suitable range. Besides, a built-in highly precision A/D converter, achieving 0.015%+0.015%F.S., 0.04%+0.04%F.S. and 0.1%+0.1%F.S. accuracy for voltage, current and power measurement espectively. Precise measurements like these are ideal for testing power efficiency and other critical parameters of the UUT's.

 

OVER CURRENT & OVER POWER TESTING

To ensure user safety and minimize power supply failure rates, overcurrent and overpower protections have to be taken into consideration during design. The 63200A enables the user to set current and power orders to test overcurrent and overpower protections, also to judge the test result as Pass or Fail on electronic load. The maximum power (Pmax) during testing can be captured and showed on the display without using an oscilloscope to verify the correctness of designed overcurrent and overpower . It can save a lot of testing time for the user.

OVER CURRENT & OVER POWER TESTING

 

USER DEFINED WAVEFORMS

In addition to common CC, CV, CP and CR loading modes of conventional loads, the 63200A accepts digital data from DAQ cards or analog data from function generators to allow for complex waveforms to be created as depicted below.

USER DEFINED WAVEFORMS

The 63200A also provides an enhanced feature, User Defined Waveform (UDW), to simulate the actual current profiles and waveforms. To reconstruct the actual current waveform, the user can upload captured waveform data into any load via a Chroma softpanel. Each load is capable of storing up to 10 sets of waveforms with each comprising up to 1.5 millions data points to meet the more strenuous test requirements.

In addition, 63200A series also provides voltage peak measurement during actual loading conditions. Avoiding the need for using an oscilloscope to capture the voltage peak, saving time and costs.

USER DEFINED WAVEFORMS

 

BATTERY DISCHARGE TESTING

The 63200A has three discharge modes: CC, CR and CP. The electronic load can set cut off voltage and time (1~100,000 sec.) to stop loading correctly and make sure the battery is not damaged due to over discharge. In addition it can measure the battery discharge power (WH, AH) and total discharge time. For example, when Load ON is pressed, the 63200A internal clock will start counting until the battery voltage is dropped to cut off voltage or Load OFF is pressed. The battery discharge testing can also apply to super capacitor for discharge time testing and so on.

BATTERY DISCHARGE TESTING

 

PROGRAMMABLE LOAD TIMING

The 63200A series electronic load has built in 255 programmable timings for various loading conditions simulation. Following lists the applications of common programmed timings.

1. Battery discharge & other applications (NPC, electric car and electric locomotive) to simulate various dynamic loading current waveform, that is to provide two levels above dynamic current simulation or one shot loading simulation.
2. Server/ Telecom power supply mixed load modulation. (For multi channels output UUT.)

PROGRAMMABLE LOAD TIMING

 

DIGITIZING FUNCTION

The 63200A series offers a digitizing function convenient for the recording of transients in both voltage and current waveforms. The following are the specifications for setting the parameters:

Sampling time:2μs ~ 40ms / resolution: 2μs (Setting the interval of sampling time)
Sampling point:1 ~ 15,000 (Setting the total sampling points)

 

COMPLEX OPERATING MODE

New complex operating modes include CR+CC, CV+CR and CV+CC modes. The CR+CC mode is suitable for power on testing and the CV+CR mode can replace Von setting while the CV+CC mode can be used for battery discharge testing.

COMPLEX OPERATING MODE

 

AUTO MODE

This mode automatically switches among CV, CR, CC and CP modes. It is suitable for lithium ion battery charger testing to get a complete V-I charging curve. Moreover, the auto mode can avoid damaging the UUT when the protection circuit is damaged.

AUTO MODE

 

SOFTPANEL

The 63200A series loads can be operated from the front panel controls or from available softpanel. This user friendly software includes all functions of the 63200A series loads and is easy to understand and operate. The 63200A loads can be controlled via GPIB, USB and Ethernet interfaces for remote control and automated testing applications.

SOFTPANEL

 

PANEL DESCRIPTION

Chroma 63200A PANEL DESCRIPTION

1. Power Switch : Electronic load AC power switch
2. Vacuum Fluorescent Display : Setup information display
3. Shortcut Keys : Loading mode switch
4. Function Keys : Including A/B key, RANGE, MODE, EXTEND, LOCK, COFIG./LOCAL, EDIT, SPEC, SHORT, RECALL, ADVA, SAVE & CLEAR
5. ENTRY Keys : Numerical keys and ENTER key
6. Arrow Keys : Changing and selecting menu
7. Push-on Knob : Editing parameter setup page, push the knob again to confirm the input value when the setting is done
8. USB Host (not ready yet) : For user defined waveform and programmed sequence data download as well as firmware upgrade

 

PANEL DESCRIPTION

9. Load Positive/Negative Terminal
10. Remote Sense Connections
11. Analog Outputs : Proportional voltage and current waveforms
12. System BUS : For master/slave system data transmission
13. System I/O : For system input/output signal control
14. GPIB & Ethernet Card Slot
15. USB Port
16. AC Input Connector

 

High Power Application

High Power Application

 

추가옵션 악세사리

선택 가능한 추가옵션
옵션명 옵션정보
63202A-150-200 Programmable High Power DC Electronic Load 150V / 200A / 2kW
63203A-150-300 Programmable High Power DC Electronic Load 150V / 300A / 3kW
63204A-150-400 Programmable High Power DC Electronic Load 150V / 400A / 4kW
63205A-150-500 Programmable High Power DC Electronic Load 150V / 500A / 5kW
63206A-150-600 Programmable High Power DC Electronic Load 150V / 600A / 6kW
63212A-150-1200 Programmable High Power DC Electronic Load 150V / 1200A / 12kW
63218A-150-1800 Programmable High Power DC Electronic Load 150V / 1800A / 18kW
63224A-150-2000 Programmable High Power DC Electronic Load 150V / 2000A / 24kW
63202A-600-140 Programmable High Power DC Electronic Load 600V / 140A / 2kW
63203A-600-210 Programmable High Power DC Electronic Load 600V / 210A / 3kW
63204A-600-280 Programmable High Power DC Electronic Load 600V / 280A / 4kW
63205A-600-350 Programmable High Power DC Electronic Load 600V / 350A / 5kW
63206A-600-420 Programmable High Power DC Electronic Load 600V / 420A / 6kW
63212A-600-840 Programmable High Power DC Electronic Load 600V / 840A / 12kW
63218A-600-1260 Programmable High Power DC Electronic Load 600V / 1260A / 18kW
63224A-600-1680 Programmable High Power DC Electronic Load 600V / 1680A / 24kW
63202A-1200-80 Programmable High Power DC Electronic Load 1200V / 80A / 2kW
63203A-1200-120 Programmable High Power DC Electronic Load 1200V / 120A / 3kW
63204A-1200-160 Programmable High Power DC Electronic Load 1200V / 160A / 4kW
63205A-1200-200 Programmable High Power DC Electronic Load 1200V / 200A / 5kW
63206A-1200-240 Programmable High Power DC Electronic Load 1200V / 240A / 6kW
63212A-1200-480 Programmable High Power DC Electronic Load 1200V / 480A /12kW
63218A-1200-720 Programmable High Power DC Electronic Load 1200V / 720A / 18kW
63224A-1200-960 Programmable High Power DC Electronic Load 1200V / 960A / 24kW
추가 구성 악세사리
악세사리 코드 악세사리 정보
A636010 Ethernet interface
A636000 GPIB interface
A632006 NI USB-6211 Bus-Powered Multifunction DAQ

카탈로그 / 매뉴얼

제품 카탈로그 제품 매뉴얼 ACROBAT PDF 리더
카탈로그 다운로드
1550453454/63200AE.pdf
등록되지 않았습니다. PDF Reader 다운로드
https://get.adobe.com/kr/reader/

관련자료

관련자료 다운로드

제품문의

등록된 상품문의

상품문의가 없습니다.